Client Profiles, Gallery, Installation, RV Adjustables

Axel Bloom Adjustable Bed for Class A Motorhome 2014 Newmar Vantana 3436

on/Comments closed

Adjustable Bed:  Custom Queen Doppelflex MX2 TWO-MOTOR ADJUSTABLE SYSTEM (29.5″ x 79.5″). To lift platform for storage access, cut back external frame 31.5 inches. (Platform hinge location is 31 inches from headboard). This results in 48 inch section of the lower external frame available to be screwed onto platform using four L-shape brackets for each adjustable bed.  This platform (with the adjustable beds and mattresses) can then be raised normally to access the storage area. During installation, customer discovered that the custom head extension we added grazed the headboard when lifted it. He cut the ends of the tops of external frame by about 2 inches for a very clean finish that resolved it.

Both half adjustable systems are synchronized to work together as the mattress is a one-piece Queen mattress. One wireless controller for raising the four-motor system.

Mattress Model: DW 800 Queen

RV Model: Newmar Vantana 2014 Model 3436

Customers: Blaise and Helen Vezie, V-Z Marine, 14460 State Hwy., 150 West, Coldspring, TX 77331

Location: Coldspring, Texas

THE BEGINNING
BOTH SUSPENSIONS RAISED.
AIR GAP BETWEEN THE FRAMES SO THEY DO NOT RUB EACH
ADEQUATE SEPARATION FROM SIDE SO FRAME WILL NOT GRAZE FIXTURE




  • ADAPTER FROM CONNECTING MOTOR TRANSFORMER TO OUTLET
  • SECOND TRANSFORMER FOR SECOND MOTOR
  • BOTH TRANSFORMERS PLACED INSIDE STORAGE COMPARTMENT
    INSIDE TUNNEL – SEE BELOW
  • THE TWO TRANSFORMER POWER CABLES ARE SIMILAR IN LENGTH BUT BECAUSE THE LOCATION OF THE MOTOR IS ON THE SIDE, ONE CABLE IS LONGER. THIS IS USEFUL TO KNOW WHEN CONNECTING THE CABLES UNDER THE PLATFORM TO POWER OUTLETS.
  • YOU CAN SEE THE LOCATIONS OF THE TRANSFORMERS FROM THE TWO SMALL GREEN LIGHTS OF THE TRANSFORMERS AT THE END OF THE TUNNEL
  • PLACED WOOD COVER OVER THE TUNNEL SO CANNOT SEE TRANSFORMERS
  • INSTALLATION OF THE SIDE STOPPER
    THAT IS CLOSE TO THE FOOT SECTION. EASIER TO INSTALL SIDE STOPPERS BY FIRST REMOVING THE SLATS AND THE RUBBER HOLSTER FROM THE TWO PLASTIC NIPPLES.
  • SIDE STOPPER LOCATION FOR THE ONE BESIDE THE HEAD REGION. AGAIN, FIRST REMOVE THE SLATS AND RUBBER HOLSTER BEFORE INSTALLING THE SIDE STOPPER
  • NOTE THAT WHEN YOU RAISE THE FOOT SECTION UP, SOMETIMES THE TWO RIGHT AND LEFT PLASTIC FEET COME OFF THE UNDERSECTION OF THE FOOT AND REMIAN ON THE BLACK ROD.
    YOU REPLACE THE TWO FEET BACK IN PLACE BY PRESSING THEM INSIDE THE RECEPTACLE OF THE FOOT SECTION UNTIL YOU FEEL A “CLICK” WHEN THE FOOT IS ENGAGED PROPERLY.
  • ALMOST FINISHED….
  • READY, SET…
  • BOTH SECTIONS ARE COMPLETE. ALL THE SIDE STOPPERS ARE IN PLACE.
  • CHECKING CLEARANCES ALL AROUND THE SUSPENSIONS IN THE NEXT SERIES OF PHOTOS
  • NOTE THAT THE HEAD SECTION IS 2 -3 INCHES AWAY FROM THE HEADBOARD SO WHEN IT IS RAISED, THE HEAD SECTION WILL NOT BRUSH AGAINST THE HEADBOARD
  • PERFECT ALIGNMENT OF THE SIDE OF THE SUSPENSION WHICH IS RESTING ON THE EDGE OF THE PLATFORM AND SUFFICIENT SPACE FROM THE WALLS
  • FINAL CHECK OF THE SPACE BETWEEN THE FRAMES
  • AGAIN, ADEQUATE SPACE ON THE LEFT SIDE
  • NOTE THAT THE TWO FOOT STOPPERS HAVE BEEN INSTALLED TO ENSUE THET WILL NOT GRAZE THE CABINETS WHEN THE SLIDER IS CLOSED
THE FINAL RESULT!
MORE TOYS